Поддержка продуктов

The maximum forward, backward, and sideward speed are all 0.8 m/s. Neither the chassis speed nor the accelerated speed are adjustable.

The 3508 motor used by the ordinary RoboMaster is equipped with a reduction gearbox, while the 3808I motor does not have a reduction gearbox, but does have an ESC.

The number “3508” refer to the size of the motor’s magnetic core. As the magnetic core of the two motors are of the same size, the names of the two motors are similar. However, they are two completely different modules.

No, it is not.

The maximum speed of the brushless motor is 1000 RPM.

To address the motors, you can go to "Settings"-"System"-"Motor Addressing" in the RoboMaster app, and operate following the prompts.

It is recommended to operate the robot on solid and flat surfaces (such as concrete, marble, wood, carpet, etc.). Operating on uneven surfaces (surfaces with fine particles like sand) may damage the Mecanum wheels or the motor.

Avoid operating the robot on uneven surfaces, otherwise particles on these surface will accelerate the wear of the Mecanum wheels and increase the noises of the wheels. You are recommended to disassemble the hub and add some lubricating grease to the shaft hole for maintenance after every 40 to 60 hours of use.

LiPo 3S.

2400 mAh.

Press and hold the battery power button for about 2 seconds to power on or off the RoboMaster EP Core.

Before charging the intelligent battery, please turn off the intelligent battery, or the power cable port may be damaged.

When the intelligent battery is used for the first time, you have to connect the charger to charge and activate the battery. The activation time takes about 15 seconds.

The max battery life during use is 85 minutes (measured at a constant speed of 0.8 m/s on a flat surface), and the charging time is 90 minutes. Note: Battery life on standby is about 100 minutes.

The intelligent battery should be stored in a dry environment. If you do not use the battery for more than 10 days, please discharge the battery to 40% to 60% before storing it. Remember to recharge and discharge the battery every 3 months or so to keep it battery active.

When the EP Core is updated, the battery is updated simultaneously. If the battery needs to be updated, the RoboMaster app will prompt "Inconsistent Firmware Version". Please update the firmware following the prompts in the app.

The RoboMaster app is specially developed for RoboMaster series robots (supporting platforms such as iOS, Android, Windows, and Mac). Search for the RoboMaster app in the App Store/Google Play/Huawei AppGallery, or scan the QR code in the User Manual to download it for your mobile device. Please go to https://www.dji.com/robomaster_app to download the desktop version for your computer.

64-bit systems for Windows 7, Windows 8, and Windows 10.

Before using a new RoboMaster EP Core for the first time, you need to activate the robot using the RoboMaster app. Please operate following the prompts in the app and complete the activation process.

The RoboMaster EP Core can be connected via Wi-Fi or a router. Please refer to the DJI tutorials for RoboMaster S1/EP/EP Core for detailed instructions: How to Connect the Robot to the App.

1. For firmware updates of the entire unit, please refer to the DJI tutorials for RoboMaster S1/EP/EP Core: How to Update RoboMaster EP’s Firmware.
2. For firmware updates of the servo/sensor adaptor module/Infrared Depth Sensor (TOF), connect the modules and make sure their module numbers do not conflict with one another. (Note: To check the servo’s number, go to Settings -> Extension Modules and check if the numbers of all connected servos are displayed normally.) If not, follow the app’s prompts and reconnect the corresponding modules. The app will prompt "Inconsistent Firmware Version" if a firmware update is required for the modules. Please follow the prompts in the app to complete the firmware update.
3. For firmware updates of other modules, please follow the prompts in the app.

Yes. You can update the firmware via desktop versions of the RoboMaster app for Windows or Mac.

iOS devices: iOS 10.0.2 and above.
Android devices: Android 5.0 and above.
Please check the official website for the compatibility list.

Before joining a network for a multiplayer battle, all robots have to connect to the RoboMaster app via the same router. Please check whether the router connection is normal.

You can go to the Settings -> Control in the RoboMaster app, and then adjust the "Control Sensitivity" to improve your operation experience.

RoboMaster EP Core does not support Follow function when it is in Solo mode.

RoboMaster EP Core is not equipped with an infrared transmitter receiver. Please use gel beads to hit the EP Core.

Recommended configuration for RoboMaster app for Windows is shown below:
CPU: 5th Generation Intel or later version, AMD or equivalent products;
GPU: GPU VRAM 1 GB and above;
Memory: 8 GB and above;
Hardware: 10 GB and above;
System: Win7 64-bit, Win8 64-bit, and Win10 64-bit