Поддержка продуктов

The RoboMaster S1’s gimbal uses two-axis stabilization.

No. The component or cables may be damaged during disassembly.

The controllable range of the tilt axis is -20° to +35°, and the controllable range of the pan axis is ±250°.

If issues occur, power off the product and check if the gimbal and other modules are mounted in place and cables are attached correctly. Also, check to make sure the gimbal can rotate smoothly without any foreign objects blocking it.

Do not mount other objects on the gimbal or apply external force to it for extended durations; otherwise, the motor may emit heat abnormally, triggering the gimbal protection mechanism and affecting usage. Also, try to avoid lifting up or adjusting the Blaster by hand. This operation may result in damage to the gimbal’s structure.

Only mobile devices with gyroscopes are supported.

A narrow-angle infrared transmitter is mounted on the front side of the Blaster, and a wide-angle infrared transmitter and an infrared receiver are mounted on both sides of the gimbal.

In order to get a better experience when using infrared beams or other infrared functions, it is recommended to operate indoors and/or in environments with low infrared light intensity.

In indoor lighting environments, the effective emission range of the narrow-angle infrared sensors is 6 meters, the effective angle is within the range of 40° to 10°, and the effective angle decreases when the distance increases. The wide-angle infrared emission can reach 360° within the range of three meters.
Note: When using outdoors or in environments with strong infrared light, the infrared sensor may be affected, and the performance may be weakened. It is recommended to use the infrared functions indoors.

HP will be deducted when the infrared beams transmitted by an S1 strike the intelligent sensing armor on another S1.

The maximum forward speed is 3.5 m/s, the maximum backward speed is 2.5 m/s, and the maximum speed when moving sideways is 2.8 m/s. To adjust acceleration speeds, launch the RoboMaster app, go to “Settings”, “Control”, “Speed” and select “Custom” to adjust.

No.

The maximum speed of the brushless motor is 1000 rpm

The driving method of the M3508I motor is FOC.

To perform addressing for the S1‘s motor, launch the RoboMaster app, go to “Settings”, “System”, and “Motor Addressing”.

It is recommended to use S1 on flat, sturdy surfaces (e.g., cement, marble, wooden floors, carpets). Uneven surfaces (e.g., as sand or dirt) may damage the Mecanum wheels or motors.

Avoid using the robots on uneven surfaces; otherwise, the Mecanum wheels may be worn down quickly and the noise of the wheels may increase. It is recommended that after every 40 to 60 hours of use, remove the hub and apply grease to the shaft hole.

Yes.

The RoboMaster S1 uses a lithium battery LiPo 3S.

2400 mAh.

Press and hold the battery power button for about two seconds to power on or off.

Yes. Keep the Intelligent Battery off while charging; otherwise, the power port may be damaged.

When using the S1 battery for the first time, the battery needs to be connected to the charger for activation. This takes about 15 seconds.

The S1 can work about 35 minutes (*measured at a constant speed of 2.0m/s on a flat surface), and it takes about 90 minutes to fully charge the battery.
*The battery life on standby is about 100 minutes.

Batteries should be stored in a waterproof and moisture-free area. If the battery is not used for more than 10 days, discharge the battery to 40-60% of the total battery level. It is also recommended users charge and discharge their battery every three months to keep it active.

When the S1 is updating, the battery will be updating at the same time. If the battery needs to be updated an “Inconsistent Firmware Found” prompt will be shown in the app. Please follow the instructions in the app to update the battery.

The RoboMaster app is an app (iOS, Android, Windows) developed specifically for the RoboMaster S1. You can search for the RoboMaster app in the App Store/Google Play, or download the mobile version of the app by scanning the QR code in the User Manual. You can also go to the official website (www.dji.com) to download the app for computers.

The 64-bit versions of Windows 7, 8, and 10 are supported.

When you connect your RoboMaster S1 to the RoboMaster app for the first time, the activation prompt will pop up automatically. Follow the activation instructions in the app. For more details, watch the tutorial video “RoboMaster S1 Tutorial - First Time Use”.

Users can connect to the RoboMaster S1 via Wi-Fi or router. For more details, watch the tutorial video “RoboMaster S1 Tutorial - How to Connect the Robot”.

For more details, watch the tutorial video “RoboMaster S1 Tutorial - Firmware Update”.

Yes. The S1 can be upgraded via the desktop version of the RoboMaster app.

Follow mode is most effective when the subject is within a range of 2-5 meters from the S1.

At present, sound from the S1 can be returned to the app, but the app cannot send voice or other sounds to the S1.

iOS devices: iOS 10.0 and above
Android devices: Android 5.0 and above
Please check the compatibility list on the official website.

In Battle mode, all S1s need to be connected via the same router simultaneously on the same network. Please check whether the network connection is normal.

Yes. Go to “Settings”, “Control”, and “Control Sensitivity” to adjust this.

Recommended configuration for RoboMaster app for Windows is shown below:
CPU: 5th Generation Intel or later version, AMD or equivalent products;
GPU: GPU VRAM 1 GB and above;
Memory: 8 GB and above;
Hardware: 10 GB and above;
System: Win7 64-bit, Win8 64-bit, and Win10 64-bit